Powermatic 1791216K Model PWBS-14CS Deluxe 14-Inch 1-3/4-Inch Woodworking Bandsaw with Bearing Guides, Lamp, and Chip Blower, 115/230-Volt 1 Phase Review
This saw replaced a Craftsmen 12" tilt table band saw. I purchased the Woodcraft anniversary package. The American Woodworker did a very good article how to tune up a band saw, this is the best one you will ever read.(also FREE videos on their sight) Out of the box the wheels were not Coplanar, in the article they showed you how to use a straight edge to measure the tires co-planer. I measured the blades top and bottom to get them in the center of the tires, For me it was easier and I think more accurate them a straight edge. The article also explained how to shim the wheels to get this critical dimension perfect, The other problem that I had was slight movement with the riser block ( fore and aft movement of the top of the saw)and tires being copanar on each side, You measure the wheels top and bottom at 3 & 9 oclock to get them even and the blade centered in all four positions measureing the blade on the tire, I used a straight edge and marked all 4 sides top and bottom of the riser block and the lines extended on to the frame so you can see how much it moved, by loosing the riser block bolt slightly with the saw tension relaxed I was able to tap the top forward or aft to achieve a perfect allignment of the blade in relation to the top and bottom wheels.The table required shimming as did the guide post. I would imagine that most saws would need a good tune up to be able to preform at the top of there capability for accurate sawing. I also see that some have problems with setting the guides and a narrow blade. What you need is a Carter Stabilizer guide. It is one bearing with a groove in the center the back of the blade rides in that replaces the top bearings and you move the lower ones away from the blade, You set your blade tracking and tension, Move the stabelizer guide to the blade and pull it toward you 1/8 inch and tighten it down, you now can use up to 1/4 inch blade that will preform like a jig saw on speed, The guy at the wood show did resawing with it, (not recommended) to show just how good the stabelizer is. He was cutting out 3d reindeers ( like the Scroll saw guy) to show you why this is recommended for scrolling. I have had this saw over one year and while I have not used it as much as I would like, so far it has been one super machine. At the Wood Magazine web sight I made the resaw jig for the band saw ( make your own lumber)and cut 12" thick wood with a 1/2" blade with no problem. They have some very good FREE videos on the band saw at their sight. Hope this helps :>)
Powermatic 1791216K Model PWBS-14CS Deluxe 14-Inch 1-3/4-Inch Woodworking Bandsaw with Bearing Guides, Lamp, and Chip Blower, 115/230-Volt 1 Phase Feature
- 14-inch band saw; built-in air pump clears chips; fully enclosed motor for longevity
- 1-1/2-horsepower motor; table tips 45-degrees right and 10-degrees left
- Solid steel and cast-iron construction for durability; built-in halogen lamp
- Includes saw, motor, blade, foot brake, work light, rip fence, mitre-gauge, chip blower
- 15-inch by 15-inch table; 44-inch table height; 20 by 34 by 68 total dimensions; 203-pounds; 1-year warranty
Powermatic 1791216K Model PWBS-14CS Deluxe 14-Inch 1-3/4-Inch Woodworking Bandsaw with Bearing Guides, Lamp, and Chip Blower, 115/230-Volt 1 Phase Overview
60 watt halogen lamp built into the body, providing direct light on blade and workpiece while cutting. Chip blower ensures a clean, visible cut line. Extra-large, two-piece cast iron table consists of a 15 x 15 tilting. (45 degrees right, 10 degrees left) section and a fixed 15 x 5 extension for a total working surface area of 15x20. Balanced, nine-spoke cast iron wheels run smoothly. Easy-to-read tensioning gauge settings indicated in blade width increments. CARTER quick tension release lever speeds blade changes. Features durable micro-adjustable dual bearing blade guide system above and below the table. Full 6 under-guide capacity with 13-1/2 frame-to-blade clearance. Built in 4 dust port. Poly V-belt maximizes power transmission while minimizing noise and vibration. Frame mounted push-button switch. Rigid one-piece welded stand requires no assembly. Includes: 1791216K 14-inch band saw, adjustable rnitre gauge, rip fence with resaw assembly, 1/4-inch band saw blade, and gooseneck work light and chip blower, and stand.
Available at Amazon Check Price Now!
Related Products
- Powermatic 1791217 Riser Block for 1791216K Bandsaw
- Powermatic 2042377 Mobile Base for Model PWBS14 Band Saw
- The Bandsaw Book
- Powermatic PM2800 1792800 18-Inch Variable Speed Drill Press
- Jet JW1031 4-Inch by 10-Feet Black Dust Collection Hose
*** Product Information and Prices Stored: Feb 20, 2010 23:50:07
0 comments:
Post a Comment